瀝青混凝土斜坡流淌值試驗儀是**檢測儀器，用于測定瀝青混凝土斜坡流淌值。適用于骨料A 大粒徑不大于26.5mm室內成型的試件和現場鉆取的芯樣。使用前務必仔細閱讀說明書。并由實驗人員操作，以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。

Asphalt concrete slope flow value tester is a testing instrument for determining asphalt concrete slope flow value. It is applicable to the test pieces for indoor molding of aggregate A with a large particle size not larger than 26.5mm and core samples drilled on site. Be sure to read the instructions carefully before use. It is operated by ** experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.

瀝青混凝土斜坡流淌值試驗儀符合DL/T5362-2006水工瀝青混凝土試驗規程。由上海榮計達儀器科技有限公司提供，設備質保期一年，一年內產品如有質量問題，供方負責免費維修。如果因操作不當或者人為損壞，我公司亦應提供維修、更換服務，由此產生的費用我公司會酌情收取。

The asphalt concrete slope flow tester conforms to DL / T5362-2006 hydraulic asphalt concrete test regulations. Provided by Shanghai Rongjida Instrument Technology Co., Ltd., the equipment warranty period is one year. If the product has quality problems within one year, the supplier is responsible for free maintenance. If due to improper operation or man-made damage, our company should also provide repair and replacement services, and the costs incurred by our company will be charged at our discretion.

瀝青混凝土斜坡流淌值試驗儀儀器的組成：

★鋼板制成：主機1臺,可放置6個試件。

★萬用電表1個。

★位移計：精度0.01mm6個。

Composition of asphalt concrete slope flow tester instrument:

★ Steel plate: 1 host machine, 6 test pieces can be placed.

★ 1 multimeter.

★ Displacement meter: 6 pcs.

瀝青混凝土斜坡流淌值試驗儀試驗步驟：

★按規定制備瀝青混合料,按規定成型馬歇爾試件,每組6個,高度63.5mm±1.3mm。從現場鉆取的芯樣,應加工成直徑為100mm±3mm,高度為63.5mm±1.3mm的試件。

★試件成型后,在室溫條件下放置24h,測量試件高度。

★采用耐高溫的高強度黏結劑將每個試件粘貼的斜坡流淌儀上,在距試件底部50mm處用高強度黏結劑粘貼8mm×3mm×1mm的銅片,在銅片的一根導線,在流淌儀板面上有一根公用導線：各銅片的導線及公用導線分別與萬用表兩**連接,調整位移計位置,使位移計測頭與銅片接觸,檢驗電路是否接通。位移計距離斜坡面垂直距離50mm。

★將斜坡坡度調整至設計規定的坡度,如無規定,斜坡坡度科采用1:1.7。

★將烘箱升至試驗溫度,溫度誤差控制在±1℃。試驗溫度可按工程實際情況確定,如無規定,可采用70℃。

★斜坡流淌儀放入烘箱前,調整位移計,讀取各試件的初讀數Uo,然后將斜坡流淌儀平穩放入已升溫至試驗溫度的烘箱內。

★恒溫48h,讀取各試件的變形值Ue。

Test steps of asphalt concrete slope flow tester:

★ Asphalt mixture is prepared according to the regulations, and Marshall test pieces are formed according to the regulations, 6 in each group, and the height is 63.5mm ± 1.3mm. Core samples drilled from the site should be processed into test pieces with a diameter of 100mm ± 3mm and a height of 63.5mm ± 1.3mm.

★ After forming the test piece, place it at room temperature for 24h and measure the height of the test piece.

★ Use a high-temperature resistant high-strength adhesive to attach each test piece to the slope flow meter. At a distance of 50mm from the bottom of the test piece, use a high-strength adhesive to paste a 8mm × 3mm × 1mm copper sheet. There is a common wire on the surface of the flow meter: the copper wire and the common wire are respectively connected to the two meters of the multimeter, adjust the position of the displacement meter, make the displacement meter contact the copper plate, and check whether the circuit is connected. The displacement meter is 50mm perpendicular to the slope surface.

★ Adjust the slope of the slope to the slope specified in the design. If there is no stipulation, the slope section will use 1: 1.7.

★ Raise the oven to the test temperature, and the temperature error is controlled at ± 1 ℃. The test temperature can be determined according to the actual situation of the project. If there is no stipulation, 70 ℃ can be used.

★ Before the slope flow meter is placed in the oven, adjust the displacement meter, read the initial reading Uo of each test piece, and then put the slope flow meter into the oven that has warmed up to the test temperature.

★ Constant temperature 48h, read the deformation value Ue of each test piece.

瀝青混凝土斜坡流淌值試驗儀試驗結果處理：

★斜坡流淌值按式計算,**至0.01mm

U=Uo-Ue

式中：

U---斜坡流淌值,mm

Uo---初讀數,mm

Ue---恒溫48h時的讀數,mm

★以每組6個試件測值的平均值作為試驗結果,若6個試件中有1個

或2個試件的流淌值與平均值之差超過10％,則取其余試件的平均值作為試驗結果：如有3個以上試件的流淌值與平均值之差超過15％,應重新試驗。

瀝青混凝土斜坡流淌值試驗儀試驗完畢后,清理表面,罩好防塵罩

Test results processing of asphalt concrete slope flow tester:

The slope flow value is calculated according to the formula, ** to 0.01mm

U = Uo-Ue

In the formula:

U --- slope flow value, mm

Uo --- initial reading, mm

Ue --- reading at constant temperature for 48h, mm

Take the average value of 6 test pieces in each group as the test result, if 1 of the 6 test pieces

Or if the difference between the flow value of the 2 test pieces and the average value exceeds 10%, then take the average value of the remaining test pieces as the test result: if the difference between the flow value of 3 or more test pieces and the average value exceeds 15%, the test.

After the asphalt concrete slope flow tester is finished, clean the surface and cover it with a dust cover.